Applicability
This example applies to all Huawei AR routers of V200R002C00 and later versions.
As shown in Figure 1:
- RouterA, RouterB, RouterC, and RouterD belong to the same AS. The four routers need to run IS-IS to implement IPv6 interworking.
- RouterA, RouterB, and RouterC belong to Area 10, and RouterD belongs to Area 20.
- RouterA and RouterB are Level-1 routers, RouterC is a Level-1-2 router, and RouterD is a Level-2 router.
1. Configure RouterA.
#
sysname RouterA
#
ipv6
//Enable IPv6 unicast forwarding.
#
isis 1 //Enable IS-IS process 1.
is-level level-1 //Set the router as a Level-1 router.
network-entity 10.0000.0000.0001.00 //Set the NET for IS-IS process 1.
#
ipv6 enable topology standard //Enable the IPv6 capability for IS-IS
process 1.
#
#
interface
GigabitEthernet1/0/0
ipv6 enable
//Enable IPv6 on the interface.
ipv6 address 10:1::2/64 //Configure a global unicast IPv6 address for
the interface.
isis ipv6 enable 1 //Enable the IPv6 capability for IS-IS
process 1 on the interface.
#
Return
2. Configure RouterB.
#
sysname RouterB
#
ipv6
#
isis 1
is-level level-1
network-entity
10.0000.0000.0002.00 //Set the NET for IS-IS process 1.
#
ipv6 enable topology standard
#
#
interface
GigabitEthernet1/0/0
ipv6 enable
ipv6 address 10:2::2/64 //Configure a global unicast IPv6 address for
the interface.
isis ipv6 enable 1
#
return
3. Configure RouterC.
#
sysname RouterC
#
ipv6
#
isis 1
network-entity
10.0000.0000.0003.00 //Set the NET for IS-IS process 1.
#
ipv6 enable topology standard
#
#
interface
GigabitEthernet0/0/0
ipv6 enable
ipv6 address 30::1/64 //Configure a global unicast IPv6 address for
the interface.
isis ipv6 enable 1
isis circuit-level
level-2 //Set the circuit type as Level-2, allowing
only Level-2 adjacencies to be established on the interface.
#
interface
GigabitEthernet1/0/0
ipv6 enable
ipv6 address 10:1::1/64 //Configure a global unicast IPv6 address for
the interface.
isis ipv6 enable 1
#
interface
GigabitEthernet2/0/0
ipv6 enable
ipv6 address 10:2::1/64 //Configure a global unicast IPv6 address for
the interface.
isis ipv6 enable 1
#
return
4. Configure RouterD.
#
sysname RouterD
#
ipv6
#
isis 1
is-level level-2 //Set the router as a Level-2 router.
network-entity
20.0000.0000.0004.00 //Set the NET for IS-IS process 1.
#
ipv6 enable topology standard
#
#
interface
GigabitEthernet1/0/0
ipv6 enable
ipv6 address 30::2/64 //Configure a global unicast IPv6 address for
the interface.
isis ipv6 enable 1
#
interface
GigabitEthernet2/0/0
ipv6 enable
ipv6 address 20::1/64 //Configure a global unicast IPv6 address for
the interface.
isis ipv6 enable 1
#
return
5. Verify the configuration.
Run the display isis route command on each
router to view IS-IS routes.
Interfaces on RouterA,
RouterB, RouterC, and RouterD can successfully ping each other.
- IPv6 must be enabled in the system view and interface view.
- The IPv6 capability must be enabled for IS-IS on interfaces.
- When using the network-entity command to set a NET for an IS-IS process, configure the same area ID for routers in an area.
The more
information about technical support you can consult with our technician - Bill,
and his e-mail address is as below:
bill@huanetwork.com
More related:
Example for Configuring the SNMP Function to Implement Communication Between the Device and the NMS
Example for Connecting Intranet Users to the Internet in Easy IP Mode
Example for Configuring the Device as a PPPoE Client to Connect Users to the Internet
How to Configure the PPPoE Client on Huawei AR1200?
Example for Connecting Intranet Users to the Internet in NAT Address Pool Mode
